LED Module Glue Filling Machine Instructional Video

LED Module Glue Filling Machine
 

LED Module Glue Filling Machine Instructional Video Part -1

This section focuses on the following:

1. This video describes the precautions for the use of the glue filling machine, including the way to add A and B glue and the role of the liquid level sensor.
2. When adding A glue, use the machine pump to extract the glue to the sensor position to stop;
3. And the B bucket of glue needs to be poured manually and cannot exceed the high liquid level sensor. When the glue is not enough, the screen will prompt to add more glue.

Click on the video to play it:

 

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -2

This section focuses on the following:

1.This video describes how to calibrate and operate the Glue Filler, including the steps of measuring the weight of Glue A, expelling air, setting parameters, agitating and cleaning the filter to ensure that the glue output matches the setpoint. It also describes the ratio of glue A and glue B and parameter settings, as well as the use of machine switches and operating buttons.
2. Key steps and precautions for machine operation
00:00 There is a glue filter here.
00:03 Clean it every three days.
00:17 After unscrewing the screws, close the valve to prevent glue leakage.
00:44 Cleaning the filter and precautions.
01:52 How to use the machine switches and operating buttons.
04:29 Glue mixing and parameter settings.
05:59 Glue mixing ratio and parameter settings.
3. Steps and precautions for using the glue machine
06:31 When using the machine for the first time, first use glue to exhaust the air in the pipe.
06:38 Setting the machine parameters to a relatively large value for glue discharge and exhaust.
07:06 Set the parameters according to the glue discharge to make sure there is no air in the pipe.
08:18 Calibrate the weight of glue discharged from the machine, you need to prepare the electronic scale.
09:39 Click on the mixing button to ensure that the substances within the glue are well mixed.
11:02 Setting the ratio of glue A and glue B. Adjusting the output as needed.
4. Glue machine parameters calibration and adjustment
11:44 Clicking, the glue button
11:47 Glue outlet starts
12:45 Measuring the actual weight of glue A and entering it into the machine
16:51 Calibrate machine parameters to ensure glue output matches setpoints

Click on the video to play it:

 

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -3

This section focuses on the following:

1. This video describes the operation of the Glue Filler, including the steps of setting the glue ratio, controlling the speed at which the working head moves, writing the program, and resetting and removing the glue mixing tube. By adjusting the ratio and working head speed, you can control the flow of glue and the amount of glue used. The video also shows how to remove and install the glue mixing tube.

Click on the video to play it:

 

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -4

This section focuses on the following:

1. This video demonstrates how to install the working head nozzle of a glue filling machine. With simple steps, you can learn how to properly install and adjust the working head nozzle to ensure proper machine operation.

Click on the video to play it:

 

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -5

This section focuses on the following:

1. This video describes that we will learn how to write machine motion paths. First click on File Management, then click on New Document, then click on OK. Then the machine returns to its initial position and we must clear all obstacles. Then click on I/O port and open the output 2 port to complete the output signal setting. Finally set the delay signal and complete the program writing.

Click on the video to play it:

 

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -6

This section focuses on the following:

1. This video details how to clean the working head and nozzle of a glue filling machine. The video emphasizes the proper sequence of operations and safety precautions when using cleaners. Steps include closing the gas valve, adding cleaner, aiming the switch at the gas and liquid, and collecting the spent cleaner. The video also demonstrates how to check for cleanliness and blow out any residual liquid before closing the valve.

Click on the video to play it:

 

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -7

This section focuses on the following:

1. The video explains the process of cleaning the working head and nozzle of a glue filling machine. This involves opening the vessel valve switch to let gas in and blowing cleaning agent into the pipe using gas. All valve switches should be opened during cleaning and closed after cleaning, in a sequential manner. It is important to remember to close the cleaning switch once the cleaning is done. The video also mentions the need for pipeline cleaning if the machine stops running for more than 10 minutes, as well as disassembling the machine for cleaning and replacing spare working heads if needed. Proper installation direction is also emphasized when assembling the working head to the robot arm.

Click on the video to play it:

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -8

This section focuses on the following:

1.In this section of the video, the focus is on the process of adding glue to the glue filling machine. The video explains the specific valves and switches involved in the process for adding Glue A to the machine. The narration provides step-by-step instructions on how to set the valve switches in order to properly add the glue. It emphasizes the importance of opening the valve switch before the machine can absorb the glue and warns against forgetting to do so to avoid any explosions or damage to the machine. The video also mentions that if prompted to add Glue B instead of Glue A, it needs to be added manually by opening the corresponding valve inlet and pouring the glue into the container.
2.In this section, the video demonstrates how to add glue A to the machine. The process involves extracting 20KG of glue A at once and then selecting the "Add glue automatically" option on the touch screen. After adding the glue, the next step is to close the automatic extraction valve switch and the manual glue adding valve switch. Then, the gas valve switch should be opened to allow gas to flow into the container. Lastly, the valve switch of the glue pump below should be closed. It is also mentioned that glue A can be added manually if desired.

Click on the video to play it:

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -9

This section focuses on the following:

1.The video demonstrates the programming process of a glue filling machine. It provides a step-by-step guide on how to program the machine efficiently. The operator is guided through selecting appropriate settings, configuring I/O ports, and setting the speed and direction of movement. The program includes steps for positioning the working head, moving to end points, and discharging the glue. The video emphasizes the importance of proper positioning and verification of the LED modules. It also suggests watching additional instructional videos for further assistance with programming machines.

Click on the video to play it:

………………………………………………………………………………………………………

LED Module Glue Filling Machine Instructional Video Part -10

This section focuses on the following:

1.The video explains the process of setting the automatic glue discharge interval for a glue filling machine, allowing users to choose the timing and duration of glue discharge. The machine provides options to discharge glue A, glue B, or both, with a maximum timing setting of 2000 seconds. The video also demonstrates how to control the thickness of the glue covering the surface of the LED module by adjusting the machining speed and the glue output. Users are able to modify the amount of glue dispensed for both glue A and glue B, ensuring the desired mixing ratio of 10:1.

Click on the video to play it:

Service Hotline:

+86 18975335491

online service
JING HE

Website QR Code

Shenzhen Jinghe Technology Co., Ltd. © 【Sitemap】 
Powered by MetInfo 5.2.7 © 2008-2025 MetInfo Inc.