SMT solder printer screen stencil cleaning machine
Ⅰ、Machine introduction
JHIMS screen template cleaning machine is a machine designed for "Water- The fourth generation screen cleaning machine designed with "Based on" technology: fully automatic cleaning, rinsing and drying process. (Using a unique double eight spray arms for cleaning and rinsing design, double four wind knives for wind cutting and drying design, cleaning and rinsing use online filtration to ensure cleanliness)
Ⅱ、Features of screen template cleaning machine
1. Fully automatic cleaning mode: the screen is thrown up and down, and the spray system sprays the heated cleaning liquid at high pressure, which can make the screen be automatically cleaned, rinsed and dried in all directions;
2. Visualization of the whole process: Visual window and LED light device, the cleaning process is clear at a glance;
3. Scientific nozzle design (patent): 8 spray arms are distributed on the left and right--thoroughly Completely solve the cleaning blind spot, the spray arm and nozzle are detachable;
4. The visual nozzle pressure is adjustable: it solves the collision and splashing problems of small workpieces under high-pressure spray conditions during cleaning;
5. Photoelectric sensors are installed at the viewing window and the stencil entrance to protect personal safety. The standard dilution tank\rinsing tank heating system greatly improves the cleaning efficiency and shortens the cleaning time;
6. Comprehensive cleaning system: compatible with water washing or chemical cleaning, for SMT; THT PCBA surface residual rosin, water-soluble flux, no-clean flux/solder paste and other organic and inorganic pollutants after welding. Thorough and effective cleaning;
7. Body quality: overall 304 stainless steel body, resistant to acid, alkaline and other cleaning liquids;
8. The built-in filter device for cleaning can realize the recycling of solvents and reduce the amount of solvents;
9. In case of solid faults, it has emergency stop button and leakage protection function;
10. Lower operating cost: lower equipment investment cost, localized service, team and sufficient spare parts supply.
Ⅲ、Fully automatic screen template cleaning machine
Cleaning area size: 750mm (L) × 750mm (W) × 40mm (H)
Equipment appearance size: 1700mm (L) × 1200mm (W) × 2100mm(H)
Power supply/gas source: three-phase five-wire system, 380V/18Kw (rated power)/0.45Mpa-0.7Mpa
Liquid tank capacity: 70L
Spray tank dilution tank heater power: 9KW
Cleaning time: 0~99 minutes (adjustable)
Cleaning temperature (liquid): room temperature~70℃ (adjustable)
Rinse time: 1 minute/time (1-59 times/adjustable)
Rinse temperature (DI water): room temperature~70℃ (adjustable)
Drying time: 0~99 minutes/(adjustable)
Cleaning size range setting: 50-750mm
Ⅳ、JHIMS screen template cleaning machine parameter configuration
Cleaning area: The cleaning liquid storage tank is used to recover and store the cleaning liquid, and the cleaning liquid is filtered, heated, monitored, and liquid level monitored in four stages.
Cleaning water pump: 2.2KW (1), 4 spray arms, 40 nozzles;
Liquid storage tank volume: ≤ 90L (1);
Filter device: stainless steel filter screen 1mm (1 piece), filter screen baffle 100 mesh (1 piece), liquid tank filter bag: 10UM (1 piece), cleaning folded filter element 0.45UM (3 pieces);
Heating power: 9KW (1), heating temperature: room temperature--70℃ (adjustable);
Liquid level protection: low position, middle position, stop position, over limit;
Spray pressure: 0.1-0.6Mpa (adjustable)
Rinsing area: The rinsing water storage tank is used to recover and store water, and the rinsing water is filtered, heated, monitored, and liquid level monitored in four stages.
Rinse water pump: 2.2KW (1 piece), 4 spray arms, 40 nozzles;
Rinse water storage tank volume: ≤90L (1 piece);
Rinse water tank heating power: 9KW (1 piece); Heating temperature: room temperature--70℃ (adjustable);
Filter device: stainless steel filter screen 1mm (1 piece), filter screen baffle 100 mesh (1 piece) liquid tank filter bag: 10UM (1 piece), cleaning folded filter element 0.45UM (3 pieces);
Liquid level protection: low position, middle position, stop position, over limit position;
Spray pressure: 0.1-0.6Mpa (adjustable)
Drying area: The drying section is used to thoroughly dry the product, and the wind is heated, cut, heated and the temperature is monitored.
Wind knife fan: 3.45KW (1 piece), stainless steel heating tube: 6KW (1 piece), 4 wind cutting wind knives, heating temperature: room temperature--60℃ (adjustable);
Screen up and down running device: The running device rotates smoothly by stepper motor, stepper driver, and encoder;
Stepper motor: 1 set Stepper driver: 400W (1 piece), 1 encoder;
.png)
.png)
skype
whatsapp
telegram
